Best Sellers

This great replacement light takes all the irritating maintenance out of your cab lights. Instead of fighting with burned-out bulbs and melted or b...

Includes chrome bezel. Sold SINGLE. This is a single function light, hardwired with two plain wires.Measures 6-5/8" by 2-1/4", with 4" between moun...

Using the standard female three-prong offset plug, the incredible Dual Revolution oval LED will light up amber, both as a marker/clearance light, a...

This sequential style differs from our SKU #12372 in that the light bar flashes from left to right (driver's side) or right to left (passenger's si...

This roll of flexible interior strip lighting can be cut every 3 diodes (2" spacing) and new 18 gauge wires (not included) soldered to the ends. So...

This light is AMBER, only. It is not part of the Dual Revolution series, although the similar looks make it a good pairing for those lights. Measur...

This chrome plastic bezel fits over any 2 inch by 6 inch trailer style rectangular LED light. This is the first time we've had a bezel with a visor...

This is a dual function light - it is hard-wired with three plain wires (ground, hot, and turn signal) and can be used as a marker or a turn signal...

Two mounting studs. This light is hard-wired with three plain wires. This light is AMBER ON BOTH SIDES when lit. These lights function at 12 volts.

Replacement bezel, only. Lights not included. This bezel is compatible with Panelite M3 LED or incandescent lights.

Tower diodes create a shattered beam effect Easy single stud installation utilizing 3/4" diameter hole 3-wire function with Roadworks' patented fem...

This is a single function light. It is effectively a single diode attached to two wires. Sold in PAIRS.

This is a dual function light, hardwired with 3 plain wires. One face is red and the other face is amber. Can be used as both a marker and a turn s...

The Infinity series has been around for awhile, long enough to gain a lot of fans. We've seen this small version of the light used on a whole range...

Please note: On all Dual Revolution Green and Purple lights, some color variation may occur as there is no DOT standard for these colors. All color...

Sold SINGLE.Features: Measures 6" x 2", with 4"between screw holes. This light is hard-wired with two male-end plugs (one positive, one negative),...

Many truckers are converting their trucks to an all-LED setup. One advantage LEDs have over incandescent lights is that they present an opportunity...

The back of this light is chrome. Measures 4-1/4" diameter x 2" deep. This light is hard-wired with three plain wires. These lights function at 12 ...

The amber turn signal is a dual-function light. There are four wires, all attached to a .180 male bullet plug. The ground wire operates both the am...

These LED replacement lights for the Grakon 1000 torpedo-style cab light housing found on many trucks, including most Peterbilts, are one of our mo...

This kit includes the Grakon 1000 housing, a foam or rubber mounting gasket, mounting bolts, LED light, and chrome visor. Whether you're starting f...

Fits the stock cab light housing for a Peterbilt 387. This product is the light, only. It does not include the chrome housing. Single function ligh...

This watermelon lens style light has a 3" diameter across the face, a 1-1/8" mounting arm, and an overall height of 4-5/8". Single-function. Hardwi...

This turn signal is perfect for the end of a boxed-end bumper, or something a little more custom - on your street rod, perhaps? One side is Amber w...

This is a dual-function, grommet mount light. Measures 5-5/16"(L) x 3-7/16(W) x 2-9/16"(T). This light requires the use of either a rubber grommet ...

Grommet mount. Has a two-prong female plug built into the back. This is a single-function light, ONLY. Grommet and wiring not included.

This is a dual-function light. It will work as both a marker and a turn signal. 3" diameter, 4-5/8" deep. Mounting stud is 1-5/8" long. 18 diodes p...

This is a dual-function light. It will work as both a marker and a turn signal. 3" diameter, 4-5/8" deep. Mounting stud is 1-5/8" long. 18 diodes p...

Measures 1" diameter. Requires an approximately 3/4" diameter hole for mounting. Single function light, threaded back, wired with two male .180 bul...

These teeny tiny dash bulbs are the smallest we have. They're even smaller than a 194! Approximately 1/8" diameter. They're commonly found in small...

These LED replacement lights for the torpedo-style cab light housing are one of our most popular items. Drivers have been waiting a long time for a...

The unique visuals of this "Halo" series marker light are a breath of fresh air. The reliability of LED diodes marries the smooth lighting of an in...

These grommet-mount lights will look great on any chicken light panel. The chrome face means they'll never clash with your paint, and the durable c...

Maxxima's marker lights are always popular with truckers. They're reliable and they look great. This pattern features 6 of Maxxima's 5mm Vantage ...

The amber turn signal is a dual-function light. There are four wires, all attached to a .180 male bullet plug. The ground wire operates both the am...

This standard-size, grommet-mount turn signal features a large bubble hump in the center for increased visibility. Perfect for truck and trailer ap...

This kit includes a single-function LED light, chrome plastic housing, and visor. This housing is an aftermarket style that replaces an existing Gr...

This light bar is durable enough to withstand all kinds of exterior applications - we've seen it mounted on bumpers, down windfins, and hidden behi...

7 Colors in 1 Light - White/Warm White/Amber/Blue/Green/Purple/Red OE Replacement Color Changing Switch with Memory Recall LED Projector Map Ligh...

Sold SINGLE. This light plugs into the existing OEM plug, which powers the amber marker/turn signal function. There is an additional hot wire, conn...

Fits Kenworth T680, T700, W990, and T880.  Also fits Peterbilt 567. Sold SINGLE. Uses the OEM plug for the marker/turn signal function. There is an...

This light's overall measurements are approximately 1" by 1-1/4", including the chrome bezel. This is a dual function (marker and turn signal) ligh...

Fits the stock cab light housing for a Peterbilt 387. This product is the light, only. It does not include the chrome housing. Single function ligh...

Want to install some great-looking LED cab lights but your housings are old and busted? Here's your solution - buy this complete kit as a well-dese...

Features: 17"(L) x 1-3/8"(W) x 1"(H). 16-1/8" between the two mounting holes. This light is a flush mount style light. Mounting hardware not incl...

This is a dual function light - it is hard-wired with three plain wires (ground, hot, and turn signal) and can be used as a marker or a turn signal...