Products

These LED replacement lights for the Grakon 1000 torpedo-style cab light housing found on many trucks, including most Peterbilts, are one of our mo...

As the name implies, these Fleet lights are economically priced, but high-quality - perfect for outfitting a large number of trucks without bankrup...

If you've been patiently awaiting the release of an economy-priced turn signal light with the diode count of an expensive one, heeeeeeeeere's Johnn...

This grommet-mount light is anything but standard. The glowing outer ring gives you the strength and endurance of an LED light, with a brand-new ty...

This design features center diodes on top and on the face, plus an outer "Halo" glowing ring. Single function only. Housing not included. These lig...

This dual-function light is hardwired with three plain wires. When this light is lit on the marker (low) side, only the outer "halo" portion is lit...

This light has 6 center diodes and an extraordinary LED-powered glowing outer ring. Sold SINGLE. Features a built-in offset 3-prong female plug.Not...

This round, pedestal light version of our "Halo" LED turn signal features a high diode count along with the signature glowing outer ring. The outer...

Our Halo Amber/Red square 59 diode LED turn signal light gives your vehicle the perfect balance of style and function. Featuring 59 diodes, you can...

There are three wires, all attached to a .180 male bullet plug. The ground wire operates both the primary and secondary functions. Includes mountin...

Measures 6" x 2", with 4" measurement between screw holes. Sold SINGLE. This light is hard-wired with two male-end plugs (one positive, one negativ...

Includes chrome bezel. Sold SINGLE. This is a single function light, hardwired with two plain wires.Measures 6-5/8" by 2-1/4", with 4" between moun...

The Infinity series has been around for awhile, long enough to gain a lot of fans. We've seen this small version of the light used on a whole range...

Lights sold separately! This product replaces the existing bezel on your Spyder ultra-low profile LED light. It will not fit any other style of lig...

This is a beacon light, NOT a strobe. It flashes much more slowly than a strobe and is intended for use only as a beacon. Hardwired with two plain ...

This light has the same optics as a glass lens incandescent, but with the reliable durability of a sealed acrylic housing! Mounts in the same 3/4" ...

This replacement load light is a great way to update the back of your sleeper. You'll increase your visibility, too. Most stock utility lights in t...

The Phantom I series is a neat little light - powered by a double bubble/tiger eye style base, but covered with a Millennium-style chrome bezel to ...

This extra-large light measures 7-7/8" long by 3-11/16" tall by 1-1/8" deep. It is a dual function light, meaning it can be used as both a marker a...

Measures 6-1/2" overall width, 5" overall height. Lights are 3.5" diameter, cab light-style lights. Sold SINGLE. This is a heavy light, so we recom...

Sold in PAIRS. This is a dual-function 1157 light bulb. The color of these bulbs may vary. The color will eventually burn off of the glass or chang...

Note: color may vary from the image shown, due to the manufacturing process of colored glass. We cannot guarantee that any two bulbs will match.

Each light functions and both a marker / clearance light and turn signal or auxiliary light. Mounts in a 3/4" diameter hole.

This LED light bar includes a short chrome mounting pedestal. These long, thin lights are perfect for steps, wind fins, or any other skinny spot be...

This long, thin strip light is perfect for interior or exterior use. It's lightweight and small enough to be mounted with double-stick tape inside ...

Features: 17"(L) x 1-3/8"(W) x 1"(H). 16-1/8" between the two mounting holes. This light is a flush mount style light. Mounting hardware not inclu...

9 diodes. Crush proof, 4 different functions. Battery powered - requires 3 AAA batteries (not included).

No other components included. This is a replacement glass lens, ONLY.

This small, 3 diode light is perfect for adding a subtle glow to your truck. Great for interior or exterior applications. Functions as a marker, on...

This bullseye/bullet rubber grommet is perfect for replacing only that single rubber piece instead of the entire light. It is 3/4" and fits most bu...

Includes mounting hardware. Sold SINGLE.

This light features 8 different internal flash patterns - including steady. No external flasher mechanism is needed! Change patterns simply by touc...

Bright, permanent mount incandescent lamp with polished reflector. 12 volt. Replacement bulbs available.Measures 5-1/4" tall by approximately 5" di...

Measures 1" diameter. Requires an approximately 3/4" diameter hole for mounting. Single function light, threaded back, wired with two male .180 bul...

This light features three bullet plugs - one ground, one marker wire, and one turn signal wire. Requires a 3/4" hole to install. Includes chrome be...

Mounts in a 3/4" diameter hole. This light has a threaded back and includes a plastic nut for installation. It is a single-function light, hardwire...

This light's overall measurements are approximately 1" by 1-1/4", including the chrome bezel. This is a dual function (marker and turn signal) ligh...

This slender clearance light is curved and ribbed on top, making the 7 diodes inside look like one long, solid line of light. The small shape lends...

This light has two bulbs inside, and mounts using a chrome base - shown as a related item. Also see related items for an upgrade to LED!

This watermelon lens style light has a 3" diameter across the face, a 1-1/8" mounting arm, and an overall height of 4-5/8". Single-function. Hardwi...

This watermelon lens style light has a 3" diameter across the face, a 2-1/8" mounting arm, and an overall height of 5-3/4". Single-function. Hardwi...

Our favorite Peterbilt-style LED is now available from two manufacturers. This one is from United Pacific. The 2 rows of 6 diodes are the same clas...

This great replacement light takes all the irritating maintenance out of your cab lights. Instead of fighting with burned-out bulbs and melted or b...

This light is hard-wired with two plain wires.

Features a watermelon-style lens (not replaceable). This single-function light is hardwired with two plain wires.Measures 3-7/8" deep (front to bac...

A simple pedestal light like this one is perfect for mirrors, bumpers, and endless applications on your motorcycle or hot rod. They're durable but ...

These lights are great for mounting to mirror arms, on the ends of your bumper, or anywhere else with space for the simple, single mounting bolt.Th...

***This light is much smaller than standard cab lights!***Measures 8" long x 2.5" wide, with 6.5" between mounting holes. This is a single function...