Best Sellers

The amber turn signal is a dual-function light. There are four wires, all attached to a .180 male bullet plug. The ground wire operates both the am...

Requires a cab light housing or special bracket for installation. Will not flush mount on its own. This is a dual-function (marker and turn signal)...

So you want to switch your cab lights over to LED, but you're not interested in a "plain jane" look. These reflectorized lights are the way of the ...

Measures 3-1/2" diameter across the light face, at the widest point. Overall length is 16-1/4", with 7-15/16" between mounting holes (measured cent...

1/2" wide by 17" long. Mounts using supplied 3M double-stick tape. Powered by three .180 male bullet plugs - one ground, one hot to power the amber...

Not only is this setup a great deal, it's also a major time saver. The lights, grommets, bezels, and wiring are all pre-installed, which saves you ...

Includes dual function (marker and turn signal) LED light and stainless steel mounting bezel. Sold SINGLE. Light measures approximately 3-5/16" dia...

Features: Measures 6-1/2" x 2" x 3/4" with 4-1/2" mounting hole centers. Please note: This light does not have ribs as shown in the dimension ...

This is the THREE wire version of this light. See related items for the four wire style. These lights are wired with the standard two male bullet s...

These lights are wired with the standard two male bullet style plugs, ground and hot, to light the amber side, plus an additional male bullet plug ...

This is not a grommet mount light. It is a surface mount light, perfect for applications like replacing the load lights in the back of your sleeper...

Measures 17" (L) x 1" x 1". This is a dual function light - will work as both a marker and a turn signal. Hardwired with three plain wires.

Like the name says, this is a truly low-profile light - measuring just 1/2" deep! Perfect for air cleaner brackets, bumpers, sunvisors, and more. ...

Electrical Built-in 2 prong female plug 12 volt Single function Design 12 Amber diodes - 2 rows of 6 6-1/4" (H) x 2-1/4" (W) x 1/4" (D) Includes...

Features: 48 amber diodes, 40 red diodes. This light is hard-wired with three plain wires. These lights function at 12 volts. One face of this li...

Measures 1" diameter. Requires an approximately 3/4" diameter hole for mounting. Single function light, threaded back, wired with two male .180 bul...

This rear center panel includes all LED lights as shown in photo. It has a unique under glow effect. Includes stainless steel backing plate and lic...

This light works excellently as a license plate/tag light, or as an extra marker light anywhere on the truck. Chrome mounting bracket not included.

Most LED lights have 5mm diodes - not these Maxxima tail lights! Their 8mm diodes are almost double the size, and you can guess what that means. As...

This light is hard-wired with one three-prong female plug, connected to the back of the light by a few inches of wire. This light is made into the...

This old-school backup light may not be as fancy as our LED styles, but it's much more affordable!

Sold SINGLE. The included LED turn signals are dual function - hardwired with three wires.  Replaces OEM part # L46-6062 and L46-6062R.

Using the standard female three-prong offset plug, the incredible Dual Revolution oval LED will light up amber, both as a marker/clearance light, a...

This is Panelite's classic M3 marker light - a staple of air cleaner light panels! The chrome plastic bezel hides the mounting screws, for a smooth...

This is a dual function light, hardwired with 4 plain wires. One face is red and the other face is amber. Can be used as both a marker and a turn s...

These LED replacement lights for the torpedo-style cab light housing are one of our most popular items. Drivers have been waiting a long time for a...

Using the standard female three-prong offset plug, the incredible Dual Revolution oval LED will light up amber, both as a marker/clearance light, a...

This sequential style differs from our SKU #12372 in that the light bar flashes from left to right (driver's side) or right to left (passenger's si...

This light is AMBER, only. It is not part of the Dual Revolution series, although the similar looks make it a good pairing for those lights. Measur...

This chrome plastic bezel fits over any 2 inch by 6 inch trailer style rectangular LED light. This is the first time we've had a bezel with a visor...

This is a dual function light - it is hard-wired with three plain wires (ground, hot, and turn signal) and can be used as a marker or a turn signal...

This light requires the use of either a rubber grommet or mounting flange. This light has a built-in two-prong female plug in the back. This light ...

Two mounting studs. This light is hard-wired with three plain wires. This light is AMBER ON BOTH SIDES when lit. These lights function at 12 volts.

Replacement bezel, only. Lights not included. This bezel is compatible with Panelite M3 LED or incandescent lights.

Tower diodes create a shattered beam effect Easy single stud installation utilizing 3/4" diameter hole 3-wire function with Roadworks' patented fem...

This is a dual function light, hardwired with 3 plain wires. One face is red and the other face is amber. Can be used as both a marker and a turn s...

The Infinity series has been around for awhile, long enough to gain a lot of fans. We've seen this small version of the light used on a whole range...

Please note: On all Dual Revolution Green and Purple lights, some color variation may occur as there is no DOT standard for these colors. All color...

Sold SINGLE.Features: Measures 6" x 2", with 4"between screw holes. This light is hard-wired with two male-end plugs (one positive, one negative),...

This Panelite marker light is longer than the M3 style, but narrower than the M1. It's a nice in-between style with 3 single-function diodes.Featur...

This is a dual-function, grommet mount light. Measures 5-5/16"(L) x 3-7/16(W) x 2-9/16"(T). This light requires the use of either a rubber grommet ...

The amber turn signal is a dual-function light. There are four wires, all attached to a .180 male bullet plug. The ground wire operates both the am...

These LED replacement lights for the Grakon 1000 torpedo-style cab light housing found on many trucks, including most Peterbilts, are one of our mo...

FIts in any standard oval rubber mounting grommet. Most compatible with Grand General brand mounting flanges.

This light functions as a backup light, ONLY. Sold SINGLE.Part of United Pacific's "Glo" series of LED lights.

This thin white light makes a great accent on trucks, motorcycles, even hot rods. Pair it with one of our chrome housings, shown as a related item,...